Bleeding

BST bleeding in wheelpaths

BST bleeding in wheelpaths

HMA bleeding from over-asphalting

Description: A film of asphalt binder on the pavement surface.  It usually creates a shiny, glass-like reflecting surface (as in the third photo) that can become quite sticky. 

Problem:  Loss of skid resistance when wet

Possible Causes: Bleeding occurs when asphalt binder fills the aggregate voids during hot weather and then expands onto the pavement surface.  Since bleeding is not reversible during cold weather, asphalt binder will accumulate on the pavement surface over time.  This can be caused by one or a combination of the following:

• Excessive asphalt binder in the HMA (either due to mix design or manufacturing)
• Excessive application of asphalt binder during BST application (as in the above figures)
• Low HMA air void content (e.g., not enough room for the asphalt to expand into during hot weather)

Repair: The following repair measures may eliminate or reduce the asphalt binder film on the pavement's surface but may not correct the underlying problem that caused the bleeding:

• Minor bleeding can often be corrected by applying coarse sand to blot up the excess asphalt binder.
• Major bleeding can be corrected by cutting off excess asphalt with a motor grader or removing it with a heater planer.  If the resulting surface is excessively rough, resurfacing may be necessary (APAI, no date given).

Block Cracking

Description: Interconnected cracks that divide the pavement up into rectangular pieces.  Blocks range in size from approximately 0.1 m² (1 ft²) to 9 m² (100 ft²).  Larger blocks are generally classified as longitudinal and transverse cracking.  Block cracking normally occurs over a large portion of pavement area but sometimes will occur only in non-traffic areas.

Problem: Allows moisture infiltration, roughness

Possible Causes: HMA shrinkage and daily temperature cycling.  Typically caused by an inability of asphalt binder to expand and contract with temperature cycles because of:

• Asphalt binder aging
• Poor choice of asphalt binder in the mix design

Repair: Strategies depend upon the severity and extent of the block cracking:

• Low severity cracks (< 1/2 inch wide).  Crack seal to prevent (1) entry of moisture into the subgrade through the cracks and (2) further raveling of the crack edges.  HMA can provide years of satisfactory service after developing small cracks if they are kept sealed (Roberts et. al., 1996).
• High severity cracks (> 1/2 inch wide and cracks with raveled edges).  Remove and replace the cracked pavement layer with an overlay.

Corrugation and Shoving

Description: A form of plastic movement typified by ripples (corrugation) or an abrupt wave (shoving) across the pavement surface.  The distortion is perpendicular to the traffic direction.  Usually occurs at points where traffic starts and stops (corrugation) or areas where HMA abuts a rigid object (shoving). 

Problem: Roughness

Possible Causes: Usually caused by traffic action (starting and stopping) combined with:

• An unstable (i.e. low stiffness) HMA layer (caused by mix contamination, poor mix design, poor HMA manufacturing, or lack of aeration of liquid asphalt emulsions)
• Excessive moisture in the subgrade

Repair: A heavily corrugated or shoved pavement should be investigated to determine the root cause of failure.  Repair strategies generally fall into one of two categories: 

• Small, localized areas of corrugation or shoving.  Remove the distorted pavement and patch. 
• Large corrugated or shoved areas indicative of general HMA failure.  Remove the damaged pavement and overlay.

Depression

Depression in left lane and shoulder

Description: Localized pavement surface areas with slightly lower elevations than the surrounding pavement.  Depressions are very noticeable after a rain when they fill with water.

Problem: Roughness, depressions filled with substantial water can cause vehicle hydroplaning

Possible Causes: Frost heave or subgrade settlement resulting from inadequate compaction during construction.

Repair: By definition, depressions are small localized areas.  A pavement depression should be investigated to determine the root cause of failure (i.e., subgrade settlement or frost heave).  Depressions should be repaired by removing the affected pavement then digging out and replacing the area of poor subgrade.  Patch over the repaired subgrade.
 

Joint Reflection Cracking

Joint reflection cracking on an arterial

Joint reflection cracking on an arterial

Joint reflection cracking close-up

Description: Cracks in a flexible overlay of a rigid pavement.  The cracks occur directly over the underlying rigid pavement joints.  Joint reflection cracking does not include reflection cracks that occur away from an underlying joint or from any other type of base (e.g., cement or lime stabilized).

Problem: Allows moisture infiltration, roughness

Possible Causes: Movement of the PCC slab beneath the HMA surface because of thermal and moisture changes.  Generally not load initiated, however loading can hasten deterioration.

Repair: Strategies depend upon the severity and extent of the cracking: 

• Low severity cracks (< 1/2 inch wide and infrequent cracks).  Crack seal to prevent (1) entry of moisture into the subgrade through the cracks and (2) further raveling of the crack edges.  In general, rigid pavement joints will eventually reflect through an HMA overlay without proper surface preparation.
• High severity cracks (> 1/2 inch wide and numerous cracks).  Remove and replace the cracked pavement layer with an overlay.

Longitudinal Cracking

Patching

Failing patch

Patch over localized distress

Utility cut patch

Description: An area of pavement that has been replaced with new material to repair the existing pavement.  A patch is considered a defect no matter how well it performs.

Problem: Roughness

Possible Causes:

• Previous localized pavement deterioration that has been removed and patched
• Utility cuts

Repair: Patches are themselves a repair action.  The only way they can be removed from a pavement's surface is by either a structural or non-structural overlay.
 

Polished Aggregate

SMAs at the NCAT test track

5 years of wear

Description: Areas of HMA pavement where the portion of aggregate extending above the asphalt binder is either very small or there are no rough or angular aggregate particles.

Problem: Decreased skid resistance

Possible Causes: Repeated traffic applications.  Generally, as a pavement ages the protruding rough, angular particles become polished.  This can occur quicker if the aggregate is susceptible to abrasion or subject to excessive studded tire wear.

Repair: Apply a skid-resistant slurry seal or BST or overlay.
 

Potholes

Pothole from fatigue cracking

Developing pothole

Description: Small, bowl-shaped depressions in the pavement surface that penetrate all the way through the HMA layer down to the base course.  They generally have sharp edges and vertical sides near the top of the hole.  Potholes are most likely to occur on roads with thin HMA surfaces (25 to 50 mm (1 to 2 inches)) and seldom occur on roads with 100 mm (4 inch) or deeper HMA surfaces (Roberts et al., 1996).

Problem: Roughness (serious vehicular damage can result from driving across potholes at higher speeds), moisture infiltration

Possible Causes: Generally, potholes are the end result of alligator cracking.  As alligator cracking becomes severe, the interconnected cracks create small chunks of pavement, which can be dislodged as vehicles drive over them.  The remaining hole after the pavement chunk is dislodged is called a pothole.

Repair: In accordance with patching techniques.
 

Raveling

Raveling due to low density

Raveling from snowplot operations

From segregation

Description: The progressive disintegration of an HMA layer from the surface downward as a result of the dislodgement of aggregate particles. 

Problem: Loose debris on the pavement, roughness, water collecting in the raveled locations resulting in vehicle hydroplaning, loss of skid resistance

Possible Causes: Several including:

• Loss of bond between aggregate particles and the asphalt binder as a result of:
  • A dust coating on the aggregate particles that forces the asphalt binder to bond with the dust rather than the aggregate
  • Aggregate Segregation.  If fine particles are missing from the aggregate matrix, then the asphalt binder is only able to bind the remaining coarse particles at their relatively few contact points.
  • Inadequate compaction during construction.  High density is required to develop sufficient cohesion within the HMA.  The third figure above shows a road suffering from raveling due to inadequate compaction caused by cold weather paving.
• Mechanical dislodging by certain types of traffic (studded tires, snowplow blades or tracked vehicles).  The first and fourth figures above show raveling most likely caused by snow plows.

Repair: A raveled pavement should be investigated to determine the root cause of failure.  Repair strategies generally fall into one of two categories:  

• Small, localized areas of raveling.  Remove the raveled pavement and patch. 
• Large raveled areas indicative of general HMA failure.  Remove the damaged pavement and overlay.

Rutting

Mix rutting

Mix rutting

Rutting from mix instability

Description: Surface depression in the wheelpath.  Pavement uplift (shearing) may occur along the sides of the rut.  Ruts are particularly evident after a rain when they are filled with water.  There are two basic types of rutting: mix rutting and subgrade rutting.  Mix rutting occurs when the subgrade does not rut yet the pavement surface exhibits wheelpath depressions as a result of compaction/mix design problems.  Subgrade rutting occurs when the subgrade exhibits wheelpath depressions due to loading.  In this case, the pavement settles into the subgrade ruts causing surface depressions in the wheelpath.

Problem: Ruts filled with water can cause vehicle hydroplaning, can be hazardous because ruts tend to pull a vehicle towards the rut path as it is steered across the rut.

Possible Causes: Permanent deformation in any of a pavement's layers or subgrade usually caused by consolidation or lateral movement of the materials due to traffic loading.  Specific causes of rutting can be:

• Insufficient compaction of HMA layers during construction.  If it is not compacted enough initially, HMA pavement may continue to densify under traffic loads.
• Subgrade rutting (e.g., as a result of inadequate pavement structure)
• Improper mix design or manufacture (e.g., excessively high asphalt content, excessive mineral filler, insufficient amount of angular aggregate particles)

Ruts caused by studded tire wear present the same problem as the ruts described here, but they are actually a result of mechanical dislodging due to wear and not pavement deformation.

Repair: A heavily rutted pavement should be investigated to determine the root cause of failure (e.g. insufficient compaction, subgrade rutting, poor mix design or studded tire wear).  Slight ruts (< 1/3 inch deep) can generally be left untreated.  Pavement with deeper ruts should be leveled and overlaid.
 

Slippage Cracking

Slippage cracking at a bus stop

Description: Crescent or half-moon shaped cracks generally having two ends pointed into the direction of traffic.

Problem: Allows moisture infiltration, roughness

Possible Causes: Braking or turning wheels cause the pavement surface to slide and deform.  The resulting sliding and deformation is caused by a low-strength surface mix or poor bonding between the surface HMA layer and the next underlying layer in the pavement structure.

Repair: Removal and replacement of affected area.
 

Stripping

Core hole showing stripping at the bottom

Stripping at bottom of hole

Fatigue failure from stripping

Description: The loss of bond between aggregates and asphalt binder that typically begins at the bottom of the HMA layer and progresses upward.  When stripping begins at the surface and progresses downward it is usually called raveling.  The third photo show the surface effects of underlying stripping.

Problem: Decreased structural support, rutting, shoving/corrugations, raveling, or cracking (alligator and longitudinal)

Possible Causes: Bottom-up stripping is very difficult to recognize because it manifests itself on the pavement surface as other forms of distress including rutting, shoving/corrugations, raveling, or cracking.  Typically, a core must be taken to positively identify stripping as a pavement distress.

• Poor aggregate surface chemistry
• Water in the HMA causing moisture damage
• Overlays over an existing open-graded surface course.  Based on WSDOT experience, these overlays will tend to strip.

Repair: A stripped pavement should be investigated to determine the root cause of failure (i.e., how did the moisture get in?). Generally, the stripped pavement needs to be removed and replaced after correction of any subsurface drainage issues.
 

Transverse (Thermal) Cracking

Large patched thermal crack

Smaller patched thermal crack

Small thermal crack

Description: Cracks perpendicular to the pavement's centerline or laydown direction.  Usually a type of thermal cracking.

Problem: Allows moisture infiltration, roughness

Possible Causes: Several including:

• Shrinkage of the HMA surface due to low temperatures or asphalt binder hardening
• Reflective crack caused by cracks beneath the surface HMA layer
• top-down cracking

Repair: Strategies depend upon the severity and extent of the cracking:

• Low severity cracks (< 1/2 inch wide and infrequent cracks).  Crack seal to prevent (1) entry of moisture into the subgrade through the cracks and (2) further raveling of the crack edges.  HMA can provide years of satisfactory service after developing small cracks if they are kept sealed (Roberts et. al., 1996).
• High severity cracks (> 1/2 inch wide and numerous cracks).  Remove and replace the cracked pavement layer with an overlay.

Water Bleeding and Pumping

Water bleeding

Water bleeding up close

CTB base pumping through HMA cracks

Description: Water bleeding (left two photos) occurs when water seeps out of joints or cracks or through an excessively porous HMA layer.  Pumping (right-most photo) occurs when water and fine material is ejected from underlying layers through cracks in the HMA layer under moving loads.

Problem: Decreased skid resistance, an indication of high pavement porosity (water bleeding), decreased structural support (pumping)

Possible Causes: Several including:

• Porous pavement as a result of inadequate compaction during construction or poor mix design
• High water table
• Poor drainage

Repair: Water bleeding or pumping should be investigated to determine the root cause.  If the problem is a high water table or poor drainage, subgrade drainage should be improved.  If the problem is a porous mix (in the case of water bleeding) a fog seal or slurry seal may be applied to limit water infiltration.